One of the popular trends in eye wear these days are known as the clip on flip up sunglasses because these things can actually replace actual sunglasses with the same quality. Now one many do not know is that it is actually possible to make this kind of accessory instead of going out to a store and buying one. Now if one is interested in trying to create one of these things, then try following some of these steps.
One can make one of these things out of some cheap sunglasses that he can just buy anywhere in stores that sell cheap items. Once he gets his hands on one, then he needs to take the screws out of the part that attaches the arms of the glasses. Remember that when one does this, the pair will not be steady anymore.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So if one is interested in making this thing, try following these steps to making clip on flip up sunglasses. This is guaranteed to be better than buying a new pair because it is cheaper and easier to use. It will also not get broken easily like an actual pair of sunglasses.
One can make one of these things out of some cheap sunglasses that he can just buy anywhere in stores that sell cheap items. Once he gets his hands on one, then he needs to take the screws out of the part that attaches the arms of the glasses. Remember that when one does this, the pair will not be steady anymore.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So if one is interested in making this thing, try following these steps to making clip on flip up sunglasses. This is guaranteed to be better than buying a new pair because it is cheaper and easier to use. It will also not get broken easily like an actual pair of sunglasses.
No comments:
Post a Comment